• En
  • kg/m
  • Timer
  • Software
  • Feedback

v2.10.89PRO

By using our site, you confirm that you have read and agree to our Cookie Policy, Privacy Policy, and our Terms of Service. It is also necessary for the normal functioning of this site. WODCAT is not affiliated with CrossFit, Inc. in any way. CrossFit is a registered trademark of CrossFit, Inc.

Stiff-Legged Deadlift

W
Deadlifts
Level: Average

The stiff-legged deadlift is a classic posterior-chain builder that targets your hamstrings, glutes, and lower back with minimal knee bend. Pulling a barbell from the floor or mid-shin with nearly straight legs packs serious strength and flexibility onto the back of your body.

Description

If your hamstrings and lower back are holding back your conventional deadlift or Olympic pulls, the stiff-legged deadlift will fix that weak link fast. Unlike a Romanian deadlift (RDL) where you start from the top and keep a soft 15-to-20-degree knee bend as your hips travel back, the stiff-legged deadlift uses almost straight legs (just unlocked so you don't hyperextend your knees) and often starts from the floor or low blocks on each rep. That extra knee extension puts a massive loaded stretch on your hamstrings and forces your spinal erectors to work harder through a longer lever arm.

Mechanically, this is a pure hip hinge with fixed, nearly straight knees. Because your knees don't bend forward to meet the bar, the barbell stays slightly further in front of your shins than in a standard deadlift or RDL, increasing the torque on your hips and lower back. You lower the weight by folding at the waist with a flat spine until you hit full hamstring stretch or touch the plates to the floor, then drive your hips forward to stand tall.

Your hamstrings, glutes, and lower back do the heavy work to extend your hips and hold your spine rigid. Your inner thighs (adductors), lats, traps, and rhomboids help pull the bar back and keep your upper back from rounding. Meanwhile, your abs, obliques, and forearm flexors lock in your core and grip.

Setup

  • Stand with your feet hip-width apart and the barbell over the middle of your feet.
  • Keep your knees almost completely straight, leaving just a tiny micro-bend so the joints aren't jammed backward.
  • Hinge at your hips with a flat back and grip the bar just outside your thighs using a double overhand or hook grip (or use lifting straps on heavy sets).
  • Pull your shoulder blades back and down, engage your lats, and look at the floor about 6 to 8 feet ahead of you to keep your neck neutral.

The Lift

  1. Brace your core and squeeze the bar off the floor (or start from a standing lockout if performing top-down reps) by driving your heels into the floor and pushing your hips forward.
  2. Keep your knees locked at that same nearly straight angle the entire way up. Do not bend your knees to scoop under the bar.
  3. Stand all the way up until your hips lock out and your torso is vertical, squeezing your glutes without leaning back at the waist.
  4. To lower the weight, unlock your hips and push your butt straight back while keeping your legs nearly straight and your spine completely flat.
  5. Lower the bar under control along a straight vertical path until the plates lightly touch the floor (or as low as your hamstring flexibility allows without your lower back rounding), then begin the next rep. Take 2 to 3 seconds on the descent to maximize the hamstring stretch.

Breathing & Bracing

  • Take a big breath into your belly before you initiate the hinge or pull from the floor, creating a 360-degree brace around your spine.
  • Hold that breath through the bottom turnaround where the lever arm on your lower back is longest.
  • Exhale near the top of the lift once your hips lock out, then reset your breath before the next rep.

Keeping It Safe

  • Lumbar disc strain: Because your legs are straight, rounding your lower back to force the plates to touch the floor puts huge shear stress on your lumbar spine. Only lower the bar as far as you can keep a flat back. If your hamstrings run out of room at mid-shin, pull from bumper plates or low blocks until your mobility improves.
  • Knee hyperextension: Locking your kneecaps all the way back under load stresses the ligaments behind your knees. Keep a barely noticeable 5-degree softness in your knees so your hamstrings take the load, not your joint capsule.
  • Hamstring pulls: Jerking the weight off the floor or bouncing plates at the bottom when your hamstrings are stretched tight can tear muscle fibers. Control the lowering phase and pause for a split second at the bottom of every rep.

Common Fixes

  • Turning it into a conventional deadlift: When the weight gets heavy, lifters naturally bend their knees at the bottom to get their quads involved. Drop the weight by 15 to 20 percent and focus on pushing the backs of your knees gently toward the wall behind you as you hinge.
  • Bar drifting way out in front: Even though the bar doesn't scrape your shins like a conventional deadlift, letting it swing inches away from your feet overloads your lower back. Squeeze oranges in your armpits to engage your lats and keep the bar hanging straight down from your shoulder blades.
  • Looking up at the mirror: Cranking your neck up at the bottom arches your neck bones and often makes your lower back lose position. Keep your chin tucked and let your head follow the angle of your torso.

Scaling & Variations

  • Tight hamstrings or beginners: Perform stiff-legged deadlifts with a pair of dumbbells or elevate the barbell on 2-inch to 4-inch blocks so you can maintain a flat lower back through the whole range of motion.
  • Making it harder: Stand on a 1-inch to 2-inch wooden platform (deficit stiff-legged deadlift) if you have great hamstring mobility, or use a 4-second eccentric tempo on the way down.