• En
  • kg/m
  • Timer
  • Software
  • Feedback

v2.10.89PRO

By using our site, you confirm that you have read and agree to our Cookie Policy, Privacy Policy, and our Terms of Service. It is also necessary for the normal functioning of this site. WODCAT is not affiliated with CrossFit, Inc. in any way. CrossFit is a registered trademark of CrossFit, Inc.

Rack pull

W
Deadlifts
Level: Average

Set a barbell on power rack pins near knee height and pull it to a full standing lockout. Rack pulls cut out the bottom half of the deadlift so you can overload your upper back, traps, glutes, hamstrings, and grip with supra-maximal weight.

Barbell

Description

If you can break a heavy deadlift off the floor just fine but stall out right past your knees, rack pulls are your fix. By starting the bar elevated on rack pins or blocks, you reduce the range of motion and take mechanical leverage off your quads. That lets you handle 10 to 20 percent more weight than your best floor deadlift, building monster lockout power and thick upper-back muscle.

Because the bar starts right around knee level, your hips begin higher and your shins stay almost vertical. It's a pure hip hinge. Once you brace and take the slack out of the bar, your hips drive forward while your knees straighten to bring the bar up your thighs to a tall standing lockout.

Your glutes, hamstrings, and lower back drive the hip extension to finish the pull. Up top, your traps, rhomboids, lats, and rear delts work hard to keep the bar tight against your thighs and hold your shoulder blades in place under crushing loads. Your forearms and wrist flexors get taxed to their limit just keeping your fingers closed around the shaft.

Setup

  • Set the safety pins inside a power rack so the barbell sits just below your kneecaps, right at your knees, or mid-thigh depending on your sticking point. Below the knee transfers best to floor deadlifts.
  • Step up to the bar with your feet hip-width apart and the bar resting roughly an inch from your shins or upper calves.
  • Hinge at your hips and grab the bar just outside your legs using a double-overhand hook grip, mixed grip, or lifting straps for heavy overload sets.
  • Pull your shoulder blades down into your back pockets, flatten your back, and keep your head neutral with your eyes fixed on a spot on the floor 8 to 10 feet ahead.

The Pull

  1. Pull up slightly on the bar to wedge your hips in and take all the slack out of the steel before the plates leave the pins.
  2. Drive your heels through the floor and push your hips forward as the bar breaks off the pins. Never yank the bar with bent elbows.
  3. Drag the bar straight up your thighs by squeezing your lats and keeping your chest rising at the same rate as your hips.
  4. Stand all the way up and squeeze your glutes to lock out your hips and knees with your shoulders back and level. Hitching the bar up your thighs or leaning backward at the top is a no-rep.
  5. Hinge your hips back first to lower the bar under control until it settles cleanly onto the pins. Let the weight come to a complete dead stop for 1 second before starting the next rep instead of bouncing the bar off the steel.

Breathing & Bracing

  • Take a huge breath into your belly and lower back at the bottom while holding onto the bar, expanding your trunk 360 degrees against your belt.
  • Hold that breath through the entire pull and lockout so your spine stays rock solid under heavy load.
  • Exhale at the top once your hips are locked, or hold your air until the bar rests safely back on the pins, then reset from scratch before the next rep.

Keeping It Safe

  • Lower back strain: Happens when you treat rack pulls as an ego contest, pile on way too much weight, and yank the bar off the pins with a rounded spine. Keep your lats tight, build up over 4 or 5 warm-up sets, and only load what you can pull with a flat back.
  • Biceps tendon tears: If you use an over-under mixed grip and bend your underhand elbow to yank the bar off the pins, you put massive strain on your distal biceps tendon. Keep both triceps flexed with elbows locked straight, or use lifting straps on your heaviest sets.
  • Hyperextending at lockout: Shoving your belly forward and leaning way back at the top crushes your lumbar facet joints without making the lift any more complete. Finish tall by squeezing your glutes, not by arching your lower back.

Common Fixes

  • Bouncing reps off the pins: Crashing the bar into the rack pins and riding the rebound up turns the drill into a dangerous ego lift and bends gym bars. Lower the bar under control, pause for a full one-count on the pins, re-brace, and pull from a dead stop.
  • Setting up like a squat: Dropping your hips too low pushes your knees forward over the bar and forces you to pull around your kneecaps. Keep your shins nearly vertical and push your hips back until your hamstrings feel loaded.
  • Bar drifting away from the thighs: If your lats go soft, the bar swings out an inch in front of your legs and hammers your lower back. Imagine squeezing oranges in your armpits to sweep the bar tight against your quads the whole way up.

Scaling & Variations

  • New to heavy hinges or no power rack available: Pull from bumper plates or wooden pulling blocks stacked on the floor, or use a trap bar on low blocks for a more upright torso position.
  • Making it harder: Add a 3-second isometric pause one inch above the pins to build starting tension, or use a snatch-width grip to hammer your upper back and traps even harder.