• En
  • kg/m
  • Timer
  • Software
  • Feedback

v2.10.89PRO

By using our site, you confirm that you have read and agree to our Cookie Policy, Privacy Policy, and our Terms of Service. It is also necessary for the normal functioning of this site. WODCAT is not affiliated with CrossFit, Inc. in any way. CrossFit is a registered trademark of CrossFit, Inc.

Power Clean and Jerk

W
Jerk
Level: Technically Complex

Rip a barbell from the floor to your shoulders in a partial squat, stand tall, and drive it overhead in one explosive dip and punch. The power clean and jerk builds total-body power, coordination, and barbell cycling speed across your glutes, quads, back, and shoulders.

Barbell

Description

In CrossFit, the power clean and jerk is what most athletes reach for when the workout calls for "Clean and Jerk" or "Ground to Overhead" at moderate weights. Skipping the full squat on the clean lets you cycle reps much faster in benchmarks like Grace, while still allowing you to move serious weight on a 1-rep max day. It tests how well you can transfer force from the floor to your shoulders, reset under fatigue, and fire that same weight straight overhead.

The lift happens in two distinct phases. First, you pull the bar off the floor with your legs, sweep it into your hips for an explosive pop, and drop into a strong quarter-squat to catch it on your front rack. After standing up to reset your feet and breath, you dip straight down a few inches, drive the bar off your shoulders with your legs, and drop under it again into a power or split receiving position with locked-out arms.

Your quads and glutes drive both the clean pull and the jerk dip-and-drive, while your hamstrings, inner thighs, and calves help launch the bar upward. Your traps, upper back, and shoulders guide the bar and catch the load, with your chest and triceps locking the barbell out overhead. Through the entire complex, your abs, obliques, and spinal erectors brace hard so your torso doesn't collapse under the catch.

Setup

  • Stand with your heels hip-width apart and the barbell right over your shoelaces. Turn your toes out slightly.
  • Squat down and grip the bar about a thumb's length outside your thighs using a hook grip (wrapping your index and middle fingers over your thumb).
  • Set your back flat, pull your shoulder blades back, and position your shoulders slightly in front of the bar with your arms completely straight.
  • Keep your chest up, eyes focused straight ahead, and weight balanced over the middle of your feet.

The Lift

  1. Push the floor away with your legs to lift the bar smoothly past your shins and knees while keeping your back angle consistent.
  2. As the bar passes your knees, sweep it back into your mid-thighs with your lats, then violently extend your hips, knees, and ankles while shrugging your shoulders.
  3. Pull yourself fast under the bar, whipping your elbows forward to catch the barbell across your front delts with your hips above parallel, then stand tall.
  4. Reset your feet under your hips, let the bar settle on your shoulders, dip straight down 3 to 4 inches with an upright torso, and drive aggressively through your heels.
  5. Punch your arms straight up while dropping under the bar into either a partial squat (push jerk) or a solid front-to-back lunge stance (split jerk) with your elbows locked out and the bar stacked over your ears. Stand all the way up with your feet together and the bar under control overhead to finish the rep. Failing to open your hips after the clean or pressing the bar out slowly without locking your elbows is a no-rep.

Breathing & Bracing

  • Take a full breath into your belly at the bottom and brace your core before pulling the bar off the floor.
  • Let out a short breath as you stand up from the power clean, then take a fresh, deep belly breath and re-brace your trunk before dipping for the jerk.
  • Hold that brace through the dip, drive, and overhead catch, exhaling only after your feet are back together and the bar is steady overhead.

Keeping It Safe

  • Lower back strain on the clean: Happens when your hips shoot up off the floor or the bar drifts out away from your shins. Keep the bar close and push with your legs off the floor instead of yanking with your lower back.
  • Wrist and elbow pain in the front rack: Usually comes from catching the bar in your palms with low elbows and absorbing the crash with your wrists. Loosen your fingertips slightly as you turn the elbows through so the bar lands squarely on the meat of your shoulders.
  • Shoulder and lower back hyperextension overhead: Dipping forward on the jerk pushes the bar out in front of you, forcing you to arch your lower back to save the lift. Keep your dip vertical like your back is sliding down a wall, and punch your head slightly through the window at lockout.

Common Fixes

  • Pulling early with the arms: Bending your elbows before your hips fully extend kills your leg power and makes the bar crash on your collarbones. Keep your arms long like ropes until your hips pop the bar upward.
  • Starfishing on the power clean: Jumping your feet out super wide just to avoid squatting below parallel destroys your knee alignment and wastes time resetting for the jerk. Practice tall power cleans, landing with your feet at a normal squat width and catching with your hips pushed back into a solid quarter-squat.
  • Pausing or leaning forward in the jerk dip: Dipping too deep or hesitating at the bottom bleeds off all the elastic bounce from your legs. Keep the dip shallow, sharp, and vertical, reversing direction immediately to launch the bar off your shoulders.

Scaling & Variations

  • Learning the mechanics or working around injuries: Break the movement down into hang power cleans plus push jerks with a lighter barbell or a pair of dumbbells so you can drill the hip pop and overhead punch without pulling from the floor.
  • Building cycling speed and heavy power: Drill touch-and-go power clean and jerks at 70 percent to smooth out your footwork between reps, or run complexes of 1 power clean plus 2 split jerks to build confidence under heavy overhead loads.