• En
  • kg/m
  • Timer
  • Software
  • Feedback

v2.10.82PRO

By using our site, you confirm that you have read and agree to our Cookie Policy, Privacy Policy, and our Terms of Service. It is also necessary for the normal functioning of this site. WODCAT is not affiliated with CrossFit, Inc. in any way. CrossFit is a registered trademark of CrossFit, Inc.

Axel Thruster

W
Thruster
Level: Average

Take a thick, non-rotating axle bar, hold it on your front rack, squat below parallel, and drive it straight overhead in one fluid motion. The axle thruster hammers your quads, glutes, shoulders, triceps, and core while testing your wrists and upper back with an unforgiving fat bar.

Barbell

Description

Regular barbell thrusters are already one of the hardest conditioning movements in CrossFit. Swapping the standard 28-millimeter olympic bar for a thick 2-inch axle bar makes everything nastier. Because an axle bar has a wide diameter and zero sleeve rotation, you can't rely on spinning bearings to save a lazy front rack, forcing your forearms, wrists, and upper back to work twice as hard on every rep.

The movement links a full front squat straight into a push press. You sit down into the hole while fighting to keep the thick tube balanced on your front delts, then drive hard out of the bottom. As your hips and knees snap to full extension at the top of the squat, that upward momentum launches the axle off your shoulders so your arms can punch it to lockout overhead.

Your quads and glutes power you out of the squat and generate the vertical pop that gets the bar moving. Your upper back, spinal erectors, abs, and obliques brace hard to keep the non-rotating bar from rolling forward and folding your chest. Once the bar leaves your shoulders, your delts, triceps, upper chest, and forearms finish the lockout and stabilize the fat bar overhead.

Setup

  • Clean the axle bar from the floor or unrack it from chest-height J-hooks onto the meat of your front delts, setting your hands just outside your shoulders.
  • Because the thick bar doesn't spin and won't sit neatly in your fingertips, keep a fuller wrap with your hands while driving your elbows up as high as your wrist mobility allows.
  • Set your feet around shoulder-width apart with your toes turned out 15 to 30 degrees.
  • Brace your abs, squeeze your glutes, and look straight ahead.

The Lift

  1. Break at your hips and knees together and sit down into a full squat, fighting to keep your elbows up so the axle doesn't roll down your arms.
  2. Push your knees out in line with your toes and keep your heels glued to the floor until your hip crease drops clearly below your kneecaps.
  3. Drive hard through your whole foot to explode out of the bottom, keeping your torso upright.
  4. Use the momentum of your hips and knees snapping open at the top to launch the axle off your shoulders, then punch straight up with your arms. Wait until your hips extend before pressing.
  5. Lock your elbows, shoulders, hips, and knees out completely at the top with the axle stacked over your ears and midfoot. Anything short of full squat depth or a stacked overhead lockout is a no-rep. Lower the bar back to your shoulders as you descend into the next rep.

Breathing & Bracing

  • Inhale deeply at the top overhead lockout or just as the axle touches your shoulders on the way down.
  • Lock in a tight 360-degree belly brace before hitting the bottom of the squat so your torso stays rigid under the fat bar.
  • Exhale forcefully as you drive through the sticking point and punch the axle overhead.

Keeping It Safe

  • Wrist and forearm strain: Trying to hold a 2-inch axle on two fingertips like an olympic barbell will bend your wrists back painfully. Keep a firmer grip around the tube with neutral wrists, and warm up your forearms and lats thoroughly.
  • Lower back overload: Letting your elbows drop in the bottom of the squat pitches the axle forward and puts heavy strain on your lumbar spine. Drive your elbows up on the descent and drop the weight if your chest collapses.
  • Bar slipping overhead: Sweat and a fat, slick steel tube make overhead grip sketchy under fatigue. Chalk your hands well and wrap your thumbs around the bar at all times.

Common Fixes

  • Pressing early out of the hole: Pushing with your arms while your knees are still bent wastes all your leg drive and fries your shoulders. Wait until your legs snap straight at the top before firing your triceps.
  • Axle rolling off the shoulders: Since the sleeves don't spin, any forward lean makes the bar want to roll away. Keep your upper back tight and focus on sitting straight down between your heels.
  • Stopping the bar out in front overhead: Lack of shoulder mobility or rushing the rep leaves the bar in front of your forehead. Push your head slightly through your arms at the top so your biceps line up with your ears.

Scaling & Variations

  • Limited wrist mobility or grip strength: Swap the axle for a standard olympic barbell to get spinning sleeves and a thinner grip, or use two dumbbells held in a neutral grip.
  • Making it harder: Perform axle cluster reps (cleaning every rep from the floor into a thruster) to test your double-overhand grip and pulling power on the fat bar.